Reminder

Welcome to the DDMALL forum.

You are currently viewing our boards as a guest which gives you limited access to post questions and access to our other features.
Only registered members may post questions, download the updated firmwares and documents.

Registration is fast, simple and absolutely free so please - Click to REGISTER!

How to use FiberOpticEnxtenderConfigTool?

DDMALL Fiber Optic Extenders enable long haul transmission of AV and RS-232 control signals at extreme distances.
Post Reply
DDM_Jim
Posts: 33
Joined: Mon Dec 23, 2019 8:24 am

How to use FiberOpticEnxtenderConfigTool?

Post by DDM_Jim » Wed Jan 08, 2020 6:19 am

How to use FiberOpticEnxtenderConfigTool?

FiberOpticEnxtenderConfigTool software can operate both the Transmitter and the receiver. Please use according to your needs.

1. Fiber Optic Enxtendser products are delivered with a black Adapter cable, as shown in Figure 1.
01.png
Figure 1
2. At the same time you need to prepare an RS232 serial cable yourself, as shown in Figure 2.
02.png
Figure 2
3. Connect the Adapter cable to the RS232 jack on the device, as shown in Figure 3.
03.png
Figure 3
4. Connect the Adapter cable to the RS232 serial cable. Connect the other end of the RS232 serial cable to the serial port of the computer, as shown in Figure 4.Note that here I only show how to connect the communication cable, you need to connect the power supply and video transmission cable when you use it.
04.png
[/b]
Figure 4
5. Open FiberOpticEnxtenderConfigTool on the computer, select the correct serial port, and select the baud rate of 57600, as shown in Figure 5.
05.PNG
Figure 5
6. If you use software to control the Transmitter, then after you enter the software, you can adjust the OSD and parameters of the Transmitter.

6.1 OSD settings. Enable the OSD, and enter the OSD text in the bottom box, click to download, after finishing FiberOpticEnxtender output screen will display the OSD content you entered, as shown in Figure 6.
06.PNG
Figure 6
You can also use an image as the OSD. Enable the Load picture option, click "image" to add the picture , and then click Download. After the download is successful, the FiberOpticEnxtender output screen will display your OSD content, as shown in Figure 7.
07.PNG
Figure 7
6.2 Parameter setting. Click the "Param Set", set the mode to "software", and then you can control the HDMI audio mode and VGA audio mode through the software, and click load after selection, as shown in Figure 8.
08.PNG
Figure 8
7. If you use software to control the receiver, then after you enter the software, you can adjust the output resolution of the receiver. Set the mode to software, then select the output resolution you want, and then click "load". The output resolution of Fiber Optic Enxtender will change, as shown in Figure 9.
09.png
Figure 9
You do not have the required permissions to view the files attached to this post.

Ranchugs
Posts: 1
Joined: Thu Feb 13, 2020 9:14 am
Location: Россия
Contact:

How to use FiberOpticEnxtenderConfigTool

Post by Ranchugs » Tue Feb 18, 2020 4:55 am

I have removed this idea :)
You do not have the required permissions to view the files attached to this post.

Mylknisy
Posts: 1
Joined: Thu Feb 13, 2020 2:16 pm
Location: Russia
Contact:

How to use FiberOpticEnxtenderConfigTool

Post by Mylknisy » Wed Feb 19, 2020 1:12 am

COULD YOU PLEASE HELP EXPLAIN TO ME HOW TO USE
F/X MOSAIC??

THERE ARE NO PARAMETERS.
ALL IT SAYS IS THAT ONE NEEDS
A SERIES OF IMAGES

?????

I AM ON WEBTV. NO PUTER.

THANK YOU
SCARLET

Beatrice Brooke
Posts: 1
Joined: Tue Mar 03, 2020 6:12 pm

Re: How to use FiberOpticEnxtenderConfigTool?

Post by Beatrice Brooke » Fri Mar 06, 2020 10:35 pm

It's so hard... :idea:

Post Reply