Reminder

Welcome to the DDMALL forum.

You are currently viewing our boards as a guest which gives you limited access to post questions and access to our other features.
Only registered members may post questions, download the updated firmwares and documents.

Registration is fast, simple and absolutely free so please - Click to REGISTER!

How to use Transport Stream in the latest firmware HEV2KW-V1.1.0.6?

If you have any questions about HEV-2KW, please leave a post here and we will try our best to solve it. Also you can share your solutions and ideas with other users here.
Post Reply
DDM_Jim
Posts: 31
Joined: Mon Dec 23, 2019 8:24 am

How to use Transport Stream in the latest firmware HEV2KW-V1.1.0.6?

Post by DDM_Jim » Sun Jan 19, 2020 10:58 am

How to use Transport Stream in the latest firmware HEV2KW-V1.1.0.6?

1.In transport stream mode, HEV-2KW sends video to a specified unicast or multicast address,they are UDP unicast and UDP multicast.UDP unicast can push the video stream to a client with a specified IP address,UDP multicast can push video streams to multiple clients but consume less bandwidth.

2.1 How to configure UDP Unicast : When you need to unicast the media stream to a client, fill in the destination client's IP address in the Destination IP field, fill in the Port (1-65535) or use the default value(8541), click "Apply",shown as in Figure 1.
05.PNG
Figure 1
2.2 How to use UDP Unicast: For example,if you need to push the stream unicast to the client with IP address 192.168.1.75. Destination IP address is 192.168. 1.75, fill in the Port (1-65535) or use the default value(8541). Make sure the client's IP address is 192.168.1.75, open the player on the client, such as VLC, and use the URL udp: //@192.168.1.75: 8541 to open the video stream,shown as in Figure 2.
10.PNG
Figure 2
3.1 How to configure UDP Multicast: When you need to push a video stream to multiple clients, fill in the Multicast IP address (Range:224.0.0.0-239.255.255.255) in the Destination IP field or use the default value (239.255.17.19), and fill in the port number (1-65535) or use the default value (8541), click "Apply",shown as in Figure 3.
04.PNG
Figure 3
3.2 How to use UDP Multicast:For example, Destination IP uses the default Multicast IP address 239.255.17.19, the port number uses the default value 8541, and after enabling UDP Multicast, each of the multiple clients use the same URL udp: //@239.255.17.19: 8541 to open video streams,shown as in Figure 4.
09.PNG
Figure 4
4.Precautions
4.1 When the HEV-2KW is in AP mode, it does not support the multicast mode,it needs to be in STA mode and connected to the router to use multicast mode.
4.2 In order to work properly in multicast mode, the device must be connected with a multicast-capable wireless router.
4.3 When you use UDP Unicast mode to push stream, you can push one video stream with maximum 8M bit rate to one client.
4.4 When you use UDP Multicast mode to push streams, you can push video streams to up to 200 clients, and each media stream supports a maximum bit rate of 8M.

The above is an introduction on how to use the Transport Stream.
Thanks.
You do not have the required permissions to view the files attached to this post.

Cardum
Posts: 1
Joined: Fri Jan 24, 2020 3:41 am
Location: Russia
Contact:

How to use Transport Stream in the latest firmware HEV2KW V1 1 0 6

Post by Cardum » Sat Apr 11, 2020 11:57 pm

I think, that you are not right. I am assured.

dellasuny
Posts: 4
Joined: Wed May 20, 2020 8:51 pm

Post by dellasuny » Wed May 20, 2020 9:21 pm

This post is really very informative i was very happy after finding this information.
I just scroll and see your beautiful ideas.keep it up.
https://olivierpatry.net/

Post Reply